Thursday, October 10, 2013

Batman Themed Bathroom ( Batman Curtains / Wayne Enterprises Candles DIY Tutorial)

Okay, for those of  you who follow my Facebook or my Instagram @nerdrendezvous you'd know I've made progress on my Batman/Batgirl themed bathroom. Mostly DIY with some altered store-bought stuff, it's going along pretty well. I thought curtains would be easy to make myself, and I was right! For once a prject that didn't turn out to be harder than I thought. So....let's begin with some SUPER EASY DIY stuff for any room, not just bathrooms!

Wayne Enterprises Decor

What you will need:
Flameless Candles (preferably wax coated)
Pencil
Printed out Wayne Enterprises logo
Scissors
Tape
Paint & Paintbrush

Cut out your logos to fit/center easily on the candle. Cover the backside of the logo paper in graphite (basically scribble all over it, nice & thick.)

Tape the logo where you'd like it on the candle, and trace over the logo with a sharp pencil.


On the left you see the taped on logo after being traced, and on the right you see what it should look like after trace.

Fill in your traced logo with paint and wait for it to dry. Make a mistake? if you have the wax coated flameless candle, you can very gently scrape off the oopsies.


Batman Logo Curtains

What you will need:
Fabric
Pins
Thread
Sewing machine
Iron-on transfer sheets you can print on with your own printer
Iron


You will need to measure out the length of the curtain rod/space you are putting the curtains.  I added a little extra so the curtain would be frilly.  You also need to measure how long you want the curtain (how far it needs to hang down) and add 3 inches to that number (you will fold that over to create the loop to slide the rod through. Here's my pithy sketch version of that sentence:


As you can see (you probably can't but I am pretending my scribbles were actually legible) I used 2.5 yards of cotton fabric that was 44 in. wide to make both curtains. Yay for planning and saving money.

You'll have to lay out your fabric right side down, mark all this out and carefully cut the two pieces out. If you did it like I did, where both curtains were cut out from the bottoms of the fabric, you won't need to put seams on the bottom of each, because the bolt of fabric they cut your material from should have sealed edges.  Fold in both smaller sides, the "ends" if you will (using mine as an example, the sides that measured 15&18.5) 1/4" and hem them.
With the right side facing down, fold the raw edge (the top, or on mine the 2.5&1.5 yrd side, you cut) over the top 2.5-3". The 2.5-3 inches will be the right side of the fabric, you will pin/sew a line 1/4" from the bottom of that edge (3" from the top of the curtain) and then sew another line 1-1.5" from the top depending on how wide your curtain rod is.

If you squint, you can see the two sewed lines on the left hand side of the picture which is the top of the curtain. I flipped the fabric over to show the right side in this pic.
Mark the center line(s) for where you want your bat(s) to go.
Iron on your bat(s) according to the iron-on sheets instructions. 

Since I had scrap I used it to make some strips for bows. Just sew the rectangular strips on to both sides of the curtain (4 pieces for two bows) and then tie them into bows.

Presto chango normal boring curtains are now gone! Also Ignore the hideous wallpaper in these pics...this is one of the reasons I decided to change my bathroom around, and will be gone as soon as I figure out what is behind it.

Custom Towel Rack

Paint
Mod Podge
Comics
Scissors
Clear Coat (Waterproof)

I simply painted my existing towel rack black and purple, used some mod podge/comics to add a few details, and then clear coated it a few times to make sure no water could harm it. Wait for it to seriously dry before exposing it to the damp bathroom conditions. I waited three days before I put it together and hung it in the bathroom. Again...ignore the wallpaper.



Tadaaaa.....another detail I added was my Haunted Arkham Asylum print by artist Abe Lopez which can be found here: http://artistabe.deviantart.com/art/Haunted-Arkham-Asylum-367228568

I am currently designing some drawer pulls and other little touches to make it a little more batty in my bathroom. Not to mention.....my newest cosplay is almost complete. I hope to release it next week or so....;)

2 comments:

  1. I really love your fake carbon paper technique on the candles - I NEVER would have thought of that!

    ReplyDelete
    Replies
    1. Right? I learned it in an art class years ago and it's saved my butt quite a few times when out of carbon paper, the down side is it is a little more smudgy, so just keep that in mind.

      Delete